92501-92_GeneSys_Manual

50 TROUBLESHOOTING GUIDE ISSUE POTENTIAL CAUSE PROPOSED SOLUTION MANUAL SECTION INSUFFICIENT WATER TO SCRUB HEAD SOLUTION SETTING TOO LOW ADJUST SOLUTION CONTROL SOLUTION DISTRIBUTION SOLUTION TANK IS EMPTY ADD WATER TO THE SOLUTION TANK SOLUTION DISTRIBUTION SOLUTION TUBE IS KINKED OR CLOGGED INSPECT TUBES SOLUTION DISTRIBUTION SOLUTION SHUTOFF VALVE IS CLOSED OPEN VALVE SOLUTION DISTRIBUTION SOLUTION PUMP IS NOT FUNCTIONING VERIFY OPERATION AND/OR REPLACE PUMP PARTS DIAGRAM STRAINER SCREEN IS CLOGGED CLEAN OUT STRAINER BOWL AND SCREEN PARTS DIAGRAM POOR WATER RECOVERY RECOVER TANK IS FULL EMPTY RECOVERY TANK RECOVERY SYSTEM DIRTY OR WORN SQUEEGEE BLADES INSPECT/ROTATE/REPLACE AS REQUIRED RECOVERY SYSTEM RECOVERY HOSE LOOSE OR KINKED INSPECT/REPAIR/REPLACE RECOVERY SYSTEM RECOVERY HOSE OR SQUEEGEE IS OBSTRUCTED CLEAR OBSTRUCTION FOR SYSTEM RECOVERY SYSTEM SQUEEGEE ASSEMBLY MAY BE OUT OF ADJUSTMENT ADJUST AS NECESSARY RECOVERY SYSTEM STUCK OR DAMAGED BALL FLOAT INSPECT/REPAIR OR REPLACE RECOVERY SYSTEM RECOVERY TANK LID IS NOT SEALING PROPERLY INSPECT SEAL AND REPLACE IF DAMAGED PARTS DIAGRAM DRAIN HOSE CAP IS NOT INSTALLED PROPERLY INSTALL DRAIN HOSE SECURELY RECOVERY SYSTEM CLOGGED HEPA FILTER REMOVE AND INSPECT INSIDE AND OUTSIDE OF HEPA FILTER. REPLACE IF DAMAGED. PARTS DIAGRAM LOW BATTERY VOLTAGE CHARGER BATTERIES CHARGING MACHINE WILL NOT TURN ON FAULTY KEY SWITCH DIAGNOSE AND REPLACE WIRING DIAGRAM DISCHARGED BATTERIES CHARGE BATTERIES CHARGING LOOSE OR DAMAGED WIRE/CONNECTION ADJUST THE MIXTURE AS REQUIRED SOLUTION DISTRIBUTION MACHINE IS NOT CLEANING PROPERLY WORN PAD OR BRUSH INSPECT AND REPLACE AS REQUIRED SCRUB DECK SETUP WRONG PAD PR BRUSH FOR APPLICATION CONTACT YOUR LOCAL DISTRIBUTOR FOR RECOMMENDED APPLICATION SCRUB DECK SETUP INSUFFICIENT CLEANING SOLUTION FOR APPLICATION ADJUST THE MIXTURE AS REQUIRED SOLUTION DISTRIBUTION VACUUM MOTOR WILL NOT SHUT OFF STILL IN DELAY MODE ALLOW 7 SECONDS TO SHUT DOWN RECOVERY SYSTEM VACUUM RELAY MAT BE FAULTY CONTACT SERVICE TECHNICIAN TO TROUBLESHOOT AND ISOLATE WIRING DIAGRAM SCRUB HEAD WILL NOT RUN SCRUB HEAD WILL NOT RAISE LOWER SCRUB HEAD SCRUB DECK SETUP BATTERY PROTECTION IS INDICATING LOW WATER SERVICE THE BATTERIES BATTERIES BATTERIES ARE LOWER THAN ALLOWABLE CHARGE BATTERIES CHARGING CIRCUIT BREAKER FOR THE BRUSH MOTORS IS TRIPPED SEE THE NEXT SECTION TITLED "SCRUB HEAD CIRCUIT BREAKERS" TROUBLING SHOOTING TABLE BAIL SWITCH IN HANDLE MAY BE FAULTY INSPECT AND REPLACE AS REQUIRED PARTS DIAGRAM BATTERY RELAY MAY BE FAULTY CONTACT SERVICE TECHNICIAN TO TROUBLESHOOT AND ISOLATE WIRING DIAGRAM SCRUB HEAD CIRCUIT BREAKER IS TRIPPED INADEQUATE SOLUTION FOR APPLICATION INCREASE SOLUTION TO SCRUB HEAD PRE-USE SETUP SCRUB HEAD IS SET ON HEAVY DOWN PRESSURE REDUCE DOWN PRESSURE SETTING PRE-USE SETUP PAD IS TOO AGGRESSIVE FOR APPLICATION CONTACT YOU LOCAL DISTRIBUTOR FOR RECOMMENDED APPLICATION PRE-USE SETUP FAULTY OR SHORTED WIRE REPAIR WIRING DIAGRAM WEAK CIRCUIT BREAKER CONTACT SERVICE TECHNICIAN TO TROUBLESHOOT AND ISOLATE. THE CIRCUIT BREAKER SHOULD NOT TRIP BELOW IT'S STATED RATING. PARTS DIAGRAM MACHINE WILL NOT DRIVE CIRCUIT BREAKER MAY BE TRIPPED INSPECT ANDRESET. IF PROBLEM PERSISTS CONTACT YOUR SERVICE TECHNICIAN PRE-USE SETUP BATTERY METER IS FLASHING A FAULT CODE REFERENCE FAULT CODE AND TROUBLESHOOT AS REQUIRED PRE-USE SETUP BATTERIES DISCHARGED TOO LOW CHARGE THE BATTERIES CHARGING SPEED KNOB TURNED ALL THE WAY DOWN INCREASE SPEED SETTING DRIVE SYSTEM FAULTY CONTROLLER CONTACT SERVICE TECHNICIAN TO TROUBLESHOOT AND ISOLATE WIRING DIAGRAM FAULTY WIRING CONTACT SERVICE TECHNICIAN TO TROUBLESHOOT AND ISOLATE WIRING DIAGRAM RUN TIME IS SHORT BATTERIES ARE LOW ON WATER(LEAD ACID ONLY) SERVICE BATTERIES BATTERIES CHARGER IS NOT PROPERLY SET FOR BATTERIES SET CHARGER TO BATTERY SPECIFICATIONS CHARGING SCRUB HEAD IS IN HIGH DOWN PRESSURE REDUCE SCRUB HEAD PRESSURE PRE-USE SETUP BATTERY CHARGER IS NOT ABLE TO FINISH CHARGE CYCLE CONFIRM A STEADY GREEN LIGHT AFTER THE CHARGE CYCLE(BEFORE UNPLUGGING FROM THE OUTLET) BATTERIES